In this video I'm going to reveal you how I constructed my 3 in 1 multipurpose workbench.I'm mosting likely to reveal you how I turned my router into a 6 Best Wood Magazines For Woodworkers WHICH WORKS , my circular saw right into a table saw as well as my jigsaw into an upside down jigsaw. Also, I'm mosting likely to show you how I gather the dust from these devices. And finally I'll reveal you how I connected as well as wired every little thing.
I devoted nearly a month in making and building this multipurpose workbench that will alleviate my future projects.In this video clip I discussed everything detailed, so it would certainly be easier for you to build one by yourself. Below you could locate a FREE PLAN with all the details included.In my next video clips you could discover some devices that I intend making for this workbench like: Table Saw Fence, Crosscut Sled, Miter Gauge, Featherboard and also Press Stick. I'll upload complimentary prepare for the accessories when I construct them.
Step 1: Reducing as well as measuring.
For this task I utilized 2 sheets of plywood, 122 x 244 centimeters, 21 mm thick. Initially I marked all dimensions. I made use of a wooden strip as a fence as well as secured it down. I put the sheets onto 2 tables to prevent the wood from splintering.I cut all the pieces that I require for this job: the top, the base, the sides, the inner panels, the doors and the structure.
Step 2: Assembling the Workbench.
I'll start with the bottom, and I'll connect the sides to it.To make the sides perpendicular with the bottom I'm making use of corner clamps. Under of the table I'm noting the points where I'll drive the screws in, and then I'm drilling some pilot openings therein. After I made the pilot openings, I made a decision that it is much better to enhance the joints with a timber adhesive, and then to drive the screws in. I'm using 5 cm long screws with 4 mm diameter. I repeated this procedure with the various other two panels which are parallel with the initial one.
To do this, I'll make pocket holes with a pocket hole jig on each rack. This is the most proper means to offer the table a cleaner look.I spent some time measuring and also securing them down with corner clamps, and after that I drove the screws in.
Step 3: Transforming the Router into a Router Table.
The very first device that I'm going to attach is the router. I measured the size of the opening, discovered its center, as well as drew a square on the panel that I need to cut with a jigsaw.Then I pierced out four holes, one in each corner to pass the jigsaw blade via. These holes will certainly be beginning factors for the jigsaw. While reducing you should attempt to remain as near to the line as possible.I have actually reduced the opening and utilized a rasp to remove all the additional wood that I couldn't reduce with the jigsaw.
Next, I need to make a rabbet for the insert that will certainly hold the router from listed below. To follow the line of the perimeter I secured down a couple of items of scrap wood.I'm making use of a straight 12 mm bit to route this section out, but I set the depth of the cut on 5 mm, so I require to pass two times on the very same surface to get the 10 mm depth.Now I need to make the inserts for the devices.
Directly Jump To:
Step 4: Transforming the Round Saw right into a Table Saw.
Now, I can carry on to the second tool, which's the circular saw. Right here, I should pay much more attention to the settling. The saw needs to be made even up with the leading edge of the workbench, so I need to measure two times before cutting.Then again, I pierced 4 openings for the jigsaw blade to travel through and made an opening as huge as the circular saw. The rasp remedied all the imperfections.
I made a rabbet with the router, and also this time I set the depth of the cut on 10 mm, so that I could eliminate the additional timber all at once.Fortunately, currently I have 10 mm thick plywood for this insert. So, I reduced the insert to dimension, as well as rounded the sides with a sandpaper.To attach the round saw to the insert I'm mosting likely to utilize the existing openings, 2 in the front, as well as two in the rear of the saw. If you can't make use of the existing ones.I noted the areas where I need to drill openings in the insert, you may have to drill brand-new openings in your saw base.